CCNA LABS OSPF ROUTING
OSPF ROUTING
 |
| OSPF ROUTING |
R1
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface GigabitEthernet0/0
Router(config-if)#ip address 192.168.10.1 255.255.255.0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#interface GigabitEthernet0/1
Router(config-if)#ip address 192.168.20.1 255.255.255.0
Router(config-if)#no shutdown
Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up
Router(config)#ROuter Ospf 10
Router(config-router)#NETwork 192.168.10.0 0.0.0.255 ARea 0
Router(config-router)#NETwork 192.168.20.0 0.0.0.255 ARea 0
00:09:48: %OSPF-5-ADJCHG: Process 10, Nbr 192.168.30.1 on GigabitEthernet0/0 from LOADING to FULL, Loading Done
Router(config-router)#NETwork 192.168.30.0 0.0.0.255 ARea 0
Router(config-router)#NETwork 192.168.20.0 0.0.0.255 ARea 0
00:12:00: %OSPF-5-ADJCHG: Process 10, Nbr 192.168.40.1 on GigabitEthernet0/1 from LOADING to FULL, Loading Done
R2
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface GigabitEthernet0/0
Router(config-if)#ip address 192.168.10.2 255.255.255.0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#interface GigabitEthernet0/1
Router(config-if)#ip address 192.168.30.1 255.255.255.0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up
Router(config)#ROuter Ospf 10
Router(config-router)#NETwork 192.168.10.0 0.0.0.255 ARea 0
Router(config-router)#NETwork 192.168.20.0 0.0.0.255 ARea 1
00:09:46: %OSPF-5-ADJCHG: Process 10, Nbr 192.168.20.1 on GigabitEthernet0/0 from LOADING to FULL, Loading Done
Router(config-router)#NETwork 192.168.30.0 0.0.0.255 ARea 1
00:14:07: %OSPF-5-ADJCHG: Process 10, Nbr 192.168.30.2 on GigabitEthernet0/1 from LOADING to FULL, Loading Done
R3
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface GigabitEthernet0/1
Router(config-if)#ip address 192.168.30.2 255.255.255.0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up
Router(config-if)#EX
Router(config)#ROuter Ospf 10
Router(config-router)#NETwork 192.168.30.0 0.0.0.255 ARea 1
00:13:58: %OSPF-5-ADJCHG: Process 10, Nbr 192.168.30.1 on GigabitEthernet0/1 from LOADING to FULL, Loading Done
R4
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface GigabitEthernet0/1
Router(config-if)#ip address 192.168.20.2 255.255.255.0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up
Router(config-if)#exit
Router(config)#interface GigabitEthernet0/0
Router(config-if)#ip address 192.168.40.1 255.255.255.0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up
Router(config)#ROuter Ospf 10
Router(config-router)#NETwork 192.168.20.0 0.0.0.255 ARea 0
00:11:51: %OSPF-5-ADJCHG: Process 10, Nbr 192.168.20.1 on GigabitEthernet0/
Router(config-router)#NETwork 192.168.40.0 0.0.0.255 ARea 2
00:12:59: %OSPF-5-ADJCHG: Process 10, Nbr 192.168.40.2 on GigabitEthernet0/0 from LOADING to FULL, Loading Done
R5
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface GigabitEthernet0/0
Router(config-if)#ip address 192.168.40.2 255.255.255.0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up
Router(config)#ROuter Ospf 10
Router(config-router)#NETwork 192.168.40.0 0.0.0.255 ARea 2
00:12:50: %OSPF-5-ADJCHG: Process 10, Nbr 192.168.40.1 on GigabitEthernet0/0 from LOADING to FULL, Loading Done
Router(config-router)#^Z
%SYS-5-CONFIG_I: Configured from console by console
Router#PING 192.168.30.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.30.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 0/2/10 ms
 |
| OUTPUT OF OSPF ROUTING |
Follow me on Instagram
Join me on LinkedIn
Follow me on FB
Subscribe the channel
Subscribe the channel
Join me on LinkedIn
Follow me on FB
Subscribe the channel
Subscribe the channel
Comments
Post a Comment