CCNA LABS Rip Routing
RIP Routing
 |
| RIP Routing |
R1
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface GigabitEthernet0/0
Router(config-if)#ip address 192.168.10.1 255.255.255.0
Router(config-if)#ip address 192.168.10.1 255.255.255.0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#interface GigabitEthernet0/1
Router(config-if)#ip address 192.168.30.1 255.255.255.0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up
Router(config-if)#EX
Router(config)#ROUter RIp
Router(config-router)#VErsion 2
Router(config-router)#NETwork 192.168.10.0
Router(config-router)#NETwork 192.168.30.0
Router(config-router)#NO AUto-summary
Router(config-router)#EX
R2
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface GigabitEthernet0/0
Router(config-if)#ip address 192.168.10.2 255.255.255.0
Router(config-if)#ip address 192.168.10.2 255.255.255.0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#interface GigabitEthernet0/1
Router(config-if)#ip address 192.168.20.1 255.255.255.0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up
Router(config-if)#EX
Router(config)#ROuter Rip
Router(config-router)#VErsion 2
Router(config-router)#NEtwork 192.168.10.0
Router(config-router)#NEtwork 192.168.20.0
Router(config-router)#NO AUto-summary
R3
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface GigabitEthernet0/1
Router(config-if)#ip address 192.168.20.2 255.255.255.0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up
Router(config-if)#exit
Router(config)#interface GigabitEthernet0/0
Router(config-if)#ip address 192.168.40.1 255.255.255.0
Router(config-if)#speed 1000
Router(config-if)#speed auto
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up
Router(config-if)#EX
Router(config)#ROuter Rip
Router(config-router)#V
Ersion 2
Router(config-router)#NEtwork 192.168.20.0
Router(config-router)#NEtwork 192.168.40.0
Router(config-router)#NO AUto-summary
Router(config-router)#EX
 |
| OUTPUT OF RIP Routing |
Comments
Post a Comment