EIGRP ROUTING USING IPV6
eigrp
r1
R1(config)#ipv
R1(config)#ipv6 uni
R1(config)#int
R1(config)#interface f0/0
R1(config-if)#ipv
R1(config-if)#ipv6 ene
R1(config-if)#ipv6 ena
R1(config-if)#ipv6 enable
R1(config-if)#ipv
R1(config-if)#ipv6 add
R1(config-if)#ipv6 address 2002::1/64
R1(config-if)#no sh
R1(config-if)#
R1(config-if)#
*Feb 8 14:36:30.535: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
R1(config-if)#
*Feb 8 14:36:30.535: %ENTITY_ALARM-6-INFO: CLEAR INFO Fa0/0 Physical Port Administrative State Down
*Feb 8 14:36:31.535: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
R1(config-if)#ex
R1(config)#ipv6 router eigrp 1
R1(config-rtr)#router-id 1.1.1.1
R1(config-rtr)#no sh
R1(config-rtr)#no shutdown
R1(config-rtr)#ex
R1(config)#int
R1(config)#interface f0/0
R1(config-if)#ipv6 eigrp 1
R1(config-if)#
*Feb 8 14:44:23.683: %DUAL-5-NBRCHANGE: IPv6-EIGRP(0) 1: Neighbor FE80::C802:DFF:FEBB:0 (FastEthernet0/0) is up: new adjacency
R1(config-if)#^Z
R1#
R1#pi
*Feb 8 14:46:15.055: %SYS-5-CONFIG_I: Configured from console by console
R1#ping 2003::2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2003::2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 12/25/52 ms
R1#
R1#
r2
R2#conf
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line. End with CNTL/Z.
R2(config)#ipv6 uni
R2(config)#int
R2(config)#interface f0/0
R2(config-if)#ipv6 ena
R2(config-if)#ipv6 address 2002::2/64
R2(config-if)#no sh
R2(config-if)#ex
R2(config)#int1
*Feb 8 14:39:00.291: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
*Feb 8 14:39:00.291: %ENTITY_ALARM-6-INFO: CLEAR INFO Fa0/0 Physical Port Administrative State Down
*Feb 8 14:39:01.291: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
R2(config)#interface f2/0
R2(config-if)#ipv6 address 2003::1/64
R2(config-if)#no sh
*Feb 8 14:39:29.099: %LINK-3-UPDOWN: Interface FastEthernet2/0, changed state to up
*Feb 8 14:39:29.099: %ENTITY_ALARM-6-INFO: CLEAR INFO Fa2/0 Physical Port Administrative State Down
*Feb 8 14:39:30.099: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet2/0, changed state to up
R2(config-if)#ex
R2(config)#ipv6 router eigrp 1
R2(config-rtr)#router-id 2.2.2.2
R2(config-rtr)#no sh
R2(config-rtr)#ex
R2(config)#interface f0/0
R2(config-if)#ipv6 eigrp 1
*Feb 8 14:44:03.203: %DUAL-5-NBRCHANGE: IPv6-EIGRP(0) 1: Neighbor FE80::C801:DFF:FEAC:0 (FastEthernet0/0) is up: new adjacency
R2(config-if)#ex
R2(config)#ipv6 router eigrp 1
R2(config-rtr)#ex
R2(config)#interface f2/0
R2(config-if)#ipv6 eigrp 1
*Feb 8 14:45:44.887: %DUAL-5-NBRCHANGE: IPv6-EIGRP(0) 1: Neighbor FE80::C803:DFF:FECA:38 (FastEthernet2/0) is up: new adjacency
R2(config-if)#^Z
*Feb 8 14:45:52.179: %SYS-5-CONFIG_I: Configured from console by console
R2#
r3
R3#conf
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line. End with CNTL/Z.
R3(config)#ipv6 uni
R3(config)#interface f2/0
R3(config-if)#ipv6 enable
R3(config-if)#ipv6 address 2003::2/64
R3(config-if)#no sh
R3(config-if)#ex
*Feb 8 14:39:01.219: %LINK-3-UPDOWN: Interface FastEthernet2/0, changed state to up
R3(config-if)#ex
R3(config)#
*Feb 8 14:39:01.219: %ENTITY_ALARM-6-INFO: CLEAR INFO Fa2/0 Physical Port Administrative State Down
*Feb 8 14:39:02.219: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet2/0, changed state to up
R3(config)#ipv6 router eigrp 1
R3(config-rtr)#router-id 3.3.3.3
R3(config-rtr)#no sh
R3(config-rtr)#ex
R3(config)#interface f2/0
R3(config-if)#ipv6 eigrp 1
*Feb 8 14:44:35.347: %DUAL-5-NBRCHANGE: IPv6-EIGRP(0) 1: Neighbor FE80::C802:DFF:FEBB:38 (FastEthernet2/0) is up: new adjacency
R3(config-if)#^Z
R3#
*Feb 8 14:44:39.239: %SYS-5-CONFIG_I: Configured from console by console
R3#ping 2002::2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2002::2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 8/15/20 ms
R3#
R3#
Comments
Post a Comment